58 mm is one check.
Compare bolt circle, thread / depth, angular datum, exit direction, plate slots, installed height and contact clearance. An M4 request is not the same thread as #6-32.
EXISTING UNIT / ENGINEERING CROSS-REFERENCE
FUTEK LAU220, LAU200
& Interface BPL Replacement Review
Start with the exact original part number. Match force range, plate stack, thread, connector and calibrated output before releasing a PFS alternative.
Compare original interfaces ↗
Original references and PFS review requirements.
| Original model / parts | Original force rating | Original geometry | Original signal / connector | PFS engineering review |
|---|---|---|---|---|
| FUTEK LAU220 ↗ FSH04395 / FSH04396 | 300 / 500 lbf (about 1,334 / 2,224 N) | Ø65.5 × 16.5 mm; 58.0 mm B.C.D.; 4 × #6-32-2B | WC1 shielded bridge; exact sensitivity / resistance from the selected part datasheet | PFS-220: compare capacity, plate stack, thread version and readout scaling separately. |
| FUTEK LAU200 ↗ FSH04404 / FSH04405; QSH02194 separate SI variant | 100 / 300 lbf; QSH02194 is a distinct 1,500 N item | Ø50.3 mm; drawing body height about 9.8 mm; 41.4 mm B.C.D. | CC4 LEMO 4-pin in the manufacturer drawing; verify receptacle view and cable revision | PFS-200: revised 10–12 mm request target is not proof of LAU200 height interchangeability. |
| Interface BPL ↗ BPL-50-C / 100-C / 200-C / 300-C / 500-C | 50 / 100 / 200 / 300 / 500 lbf standard capacities | 2.57 × 2.58 × 0.88 in stated on the original product page | Original A:+Exc; B:+Sig; C:−Sig; D:−Exc; E/F:NC. Connector orientation still required. | PFS-220: compare plate, capacity and cable termination. Original nominal SI labels are not exact unit conversions. |
| Michigan Scientific BPFT ↗ BPFT; BPFT2 / BPFT3 require their own drawings | 500 lb on the original BPFT page | Pedal-specific clamp / pad; exact geometry follows the selected manufacturer drawing | Strain-gauge bridge; do not assume one impedance or output applies to all BPFT variants | Supply the full BPFT variant, clamp size and calibration record with a PFS replacement request. |
| Racelogic VBOX RLACS282 ↗ RLACS282; RLACS292 event-marker interface is separate | 150 kgf (about 1,471 N) | Ø75 × 24.5 mm body; 27.5 mm with mounting bracket in the cited datasheet | Conditioned 0–5V; 8.5–28V supply in the cited datasheet | Review the complete conditioned signal chain and event-marker interface, not only the bare bridge. |
Sources can change; confirm the current drawing revision. Standard lbf capacities and rounded catalog SI labels are not interchangeable nominal ratings. PFS is independent of all named manufacturers.
A bridge is a circuit.
Confirm resistance, excitation current / voltage, sensitivity, shunt calibration, shield termination and pin view. Do not assign one 350 Ω or 700 Ω value to every manufacturer variant.
Scope the complete package.
Original LAU drawings list supplied mounting / case items. Check the dated quotation before treating every accessory as an extra charge. Compare sensor, cable, mount, readout and calibration on the same basis.
COMPARABLE QUOTATIONS / BUYER INPUT
Compare the same measurement package.
Enter two dated quotations in one currency. Include zero explicitly where an item is included. The result is purchasing arithmetic, not a published PFS price or a product-performance comparison.
Keep tax, freight, quantity, delivery and currency basis consistent. Negative difference means the entered PFS quote is higher.
Attach the evidence your replacement review needs.
- Identify: original nameplate, complete part number, capacity, serial number and drawing revision.
- Describe: installed pedal / fixture dimensions, original cable pinout, readout model and the test sequence.
- Agree: proposed PFS drawing, signal-chain mapping, calibration scope, acceptance tests and formal quotation.
CONTINUE YOUR SELECTION
From pedal load to usable data.
ENGINEERING / REQUEST
Build the right
measurement chain.
Send your force range, pedal dimensions and acquisition requirements. Request a mounting drawing, CAD review and a complete sensor / readout quotation.
Replacing an existing sensor?
Include the exact part number, drawing revision, connector pinout and calibration requirements. Compatibility is reviewed per configuration.
Corporate procurement requests
Include your purchasing entity, PO requirements, destination and required invoice / calibration documents. Payment options, trade terms, freight and delivery are confirmed in the written quotation.